rectifier specialists r features * glass passivated junction * 5000 watts peak pulse power capability on 10/1000 ms waveform * excellent clamping capability * low zener impedance * fast response time mechanical data 5.0smdj11 thru 5.0smdj440ca technical specifications of transient voltage suppressor voltage range - 11 to 440volts peak pulae power - 5000 watts dimensions in inches and (millimeters) devices for bipolar applications for bidirectional use c or ca suffix (e.g. 5.0smdj11c, 5.0smdj440ca). electrical characteristics apply in both directions dc components co., ltd. ratings at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load, for capacitive load, derate current by 20%. maximum ratings and electrical characteristics 60hzresistive or inductive load maximum instantaneuos forwaard voltage at 50a for unidirectional only peak pulse power dissipation on 10/1000 ms waveform(note1,fig.1) steady state power dissipation at t = 75 oclead lengths .375"(9.5mm) (note 2) peak forward surge current, 8.3ms single half sine-wave superimposed on rated load(jedec method) (note 3) operating and storage temperature range symbol pppm p m(av) ifsm tj , tstg vf value minimum 5000 6.5 300 -55 to + 175 3.5 units watts watts oc amps volts notes : 1. non-repetitive current pulse, per fig.3 and derated above ta = 25 o c per fig. 2. 2. mounted on copper leaf area of 0.8 x 0.8"( 20 x 20mm ) per fig. 5 3. 8.3ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum. smc (do-214ab) .245(6.2).220(5.6) .280(7.1).260(6.6) .128(3.3).108(2.8) .012(0.3).004(0.1) .008(0.2).004(0.1) .060(1.5).030(0.8) .102(2.6).079(2.0) .320(8.1).303(7.7) * case: molded plastic * epoxy: ul 94v- 0 rate flame retardant * mounting position: any * weight: 0.24 gram *terminals: solder plated solderable per mil-std-750, method 2026 * polarity: as marked
r dc components co., ltd. rating and characteristic curves ( 5.0smdj11 thru 5.0smdj440ca ) fig. 1 - peak pulse power rating curve non-repetitive pulse waveform shown in fig.3t a = 25oc 0.1 1.0 10 100 0.1ms 1.0ms 10ms 100ms 1.0ms 10ms ppm, peak pulse power, kw t p, pulse width, sec peak pulse power (ppp) or current (ipp ) derating in percentage, % 0 ta , ambient temperature, (oc) fig. 2 - pulse derating curve 0 25 50 75 100 25 50 75 100 125 150 175 200 fig. 3 - pulse waveform ippm , peak pulse current, % tr = 10 msec. pulse width (td) is definedas the point where the peak current decays to 50% of i ppm peak value i ppm half value - ippm 210/1000 m sec. waveform as defined by r.e.a. td 0 0 50 100 150 1.0 2.0 3.0 4.0 t, time, ms 10 100 10000 100000 cj , capacitance, pf fig. 4 - typical junction capacitance f = 1.0 mhzvsig = 50mvp-p t j = 25oc 1.0 100 500 v(br) , breakdown voltage, volts fig. 5 - steady state power derting curve pm (av), steady state power dissiation, watts 60hzresistive or inductive load tl, lead temperature ( oc) 0 0 2 4 6 8 25 50 75 100 125 150 175 200 300 400 fig. 6 - maximum non-repetitive forward surge current unidirectional ifsm , peak forward surge current amperes 8.3ms single half sine-wave (jedec method) number of cycles at 60 hz 1 10 100 0 vr = rated stand-off voltage measured atzero bias 200 l = 0.375?(9.5mm) lead lengths 0.8x0.8x0.040?(20x20mm) copper heat sinks
r dc components co., ltd. 5.0smdj (5000w) series transient voltage suppressors 5.0smdj11 11 12.2 14.9 1 800 20.1 251.24 5.0smdj11a 11 12.2 13.5 1 800 18.2 277.47 5.0smdj12 12 13.3 16.3 1 800 22.0 229.55 5.0smdj12a 12 13.3 14.7 1 800 19.9 253.77 5.0smdj13 13 14.4 17.6 1 500 23.8 212.18 5.0smdj13a 13 14.4 15.9 1 500 21.5 234.88 5.0smdj14 14 15.6 19.1 1 200 25.8 195.74 5.0smdj14a 14 15.6 17.2 1 200 23.2 217.67 5.0smdj15 15 16.7 20.4 1 100 26.9 187.73 5.0smdj15a 15 16.7 18.5 1 100 24.4 206.97 5.0smdj16 16 17.8 21.8 1 50 28.8 175.35 5.0smdj16a 16 17.8 19.7 1 50 26.0 194.23 5.0smdj17 17 18.9 23.1 1 20 30.5 165.57 5.0smdj17a 17 18.9 20.9 1 20 27.6 182.97 5.0smdj18 18 20.0 24.4 1 10 32.2 156.83 5.0smdj18a 18 20.0 22.1 1 10 29.2 172.95 5.0smdj19 19 21.13 25.76 1 10 34.0 148.49 5.0smdj19a 19 21.13 23.3 1 10 30.8 164.07 5.0smdj20 20 22.2 27.1 1 5 35.8 141.06 5.0smdj20a 20 22.2 24.5 1 5 32.4 155.86 5.0smdj22 22 24.4 29.8 1 5 39.4 128.17 5.0smdj22a 22 24.4 26.9 1 5 35.5 142.25 5.0smdj24 24 26.7 32.6 1 5 43.0 117.44 5.0smdj24a 24 26.7 29.5 1 5 38.9 129.82 5.0smdj26 26 28.9 35.3 1 5 46.6 108.37 5.0smdj26a 26 28.9 31.9 1 5 42.1 119.95 5.0smdj28 28 31.1 38.0 1 5 50.0 101.00 5.0smdj28a 28 31.1 34.4 1 5 45.4 111.23 5.0smdj30 30 33.3 40.7 1 5 53.5 94.39 5.0smdj30a 30 33.3 36.8 1 5 48.4 104.34 5.0smdj33 33 36.7 44.9 1 5 59.0 85.59 5.0smdj33a 33 36.7 40.6 1 5 53.3 94.75 5.0smdj36 36 40.0 48.9 1 5 64.3 78.54 5.0smdj36a 36 40.0 44.2 1 5 58.1 86.92 5.0smdj40 40 44.4 54.3 1 5 71.4 70.73 5.0smdj40a 40 44.4 49.1 1 5 64.5 78.29 5.0smdj43 43 47.8 58.4 1 5 76.7 65.84 5.0smdj43a 43 47.8 52.8 1 5 69.4 72.77 5.0smdj45 45 50.0 61.1 1 5 80.3 62.89 5.0smdj45a 45 50.0 55.3 1 5 72.7 69.46 5.0smdj48 48 53.3 65.1 1 5 85.5 59.06 5.0smdj48a 48 53.3 58.9 1 5 77.4 65.25 5.0smdj51 51 56.7 69.3 1 5 91.1 55.43 5.0smdj51a 51 56.7 62.7 1 5 82.4 61.29 5.0smdj54 54 60.0 73.3 1 5 96.3 52.44 5.0smdj54a 54 60.0 66.3 1 5 87.1 57.98 5.0smdj58 58 64.4 78.7 1 5 103 49.03 5.0smdj58a 58 64.4 71.2 1 5 93.6 53.95 5.0smdj60 60 66.7 81.5 1 5 107 47.20 5.0smdj60a 60 66.7 73.7 1 5 96.8 52.17 reverse stand-off voltage breakdown voltage @ it test current it v rwm maximum reverse leakage @ v rwm maximum clamping voltage @ ipp maximum peak pulse current vbr v min. max. v v ma ma ma uni- bi- i r v c ipp v a type
r dc components co., ltd. 5.0smdj (5000w) series transient voltage suppressors 5.0smdj64 64 71.1 86.9 1 5 114 44.30 5.0smdj64a 64 71.1 78.6 1 5 103 49.03 5.0smdj70 70 77.8 95.1 1 5 125 40.40 5.0smdj70a 70 77.8 86.0 1 5 113 44.69 5.0smdj75 75 83.3 102 1 5 134 37.69 5.0smdj75a 75 83.3 92.1 1 5 121 41.74 5.0smdj78 78 86.7 106 1 5 139 36.33 5.0smdj78a 78 86.7 95.8 1 5 126 40.08 5.0smdj80 80 88.8 108.8 1 5 143.2 35.27 5.0smdj80a 80 88.8 97.6 1 5 129.6 38.97 5.0smdj85 85 94.4 115 1 5 151 33.44 5.0smdj85a 85 94.4 104 1 5 137 36.86 5.0smdj90 90 100 122 1 5 160 31.56 5.0smdj90a 90 100 111 1 5 146 34.59 5.0smdj100 100 111 136 1 5 179 28.21 5.0smdj100a 100 111 123 1 5 162 31.17 5.0smdj110 110 122 149 1 5 196 25.77 5.0smdj110a 110 122 135 1 5 177 28.53 5.0smdj120 120 133 163 1 5 214 23.60 5.0smdj120a 120 133 147 1 5 193 26.17 5.0smdj130 130 144 176 1 5 231 21.86 5.0smdj130a 130 144 159 1 5 209 24.16 5.0smdj140 140 155 190.4 1 5 250.6 20.15 5.0smdj140a 140 155 171 1 5 226.8 22.27 5.0smdj150 150 167 204 1 5 268 18.84 5.0smdj150a 150 167 185 1 5 243 20.78 5.0smdj160 160 178 218 1 5 287 17.60 5.0smdj160a 160 178 197 1 5 259 19.50 5.0smdj170 170 189 231 1 5 304 16.61 5.0smdj170a 170 189 209 1 5 275 18.36 5.0smdj180 180 200 244.8 1 5 322.2 15.67 5.0smdj180a 180 200 220 1 5 291.6 17.32 5.0smdj190 190 211 258.4 1 5 340.1 14.85 5.0smdj190a 190 211 232 1 5 307.8 16.41 5.0smdj200a 200 224 247 1 5 324 9.26 5.0smdj220a 220 246 272 1 5 356 8.43 5.0smdj250a 250 279 309 1 5 405 7.41 5.0smdj300a 300 335 371 1 5 486 6.17 5.0smdj350a 350 391 432 1 5 567 5.29 5.0smdj400a 400 447 494 1 5 648 4.63 5.0smdj440a 440 492 543 1 5 713 4.21 reverse stand-off voltage breakdown voltage @ it test current it v rwm maximum reverse leakage @ v rwm maximum clamping voltage @ ipp maximum peak pulse current vbr v min. max. v v ma ma ma uni- bi- i r v c ipp v a type notes: 1. vbr measured after it applied for 300ms. it = square wave pulse or equivalent. 2. for bidirectional use ?c? or ?ca ? suffixs for all types (e.g.: 5.0smdj5.0c, 5.0smdj5.0ca, 5.0smdj440 c, 5.0smdj440ca).electrical characteristics apply in both directions.3. for bidirectional types having v rwm of 10 volts and less, the id limit is doubled.
|